![encrypt files testout lab simulator encrypt files testout lab simulator](https://www.coursehero.com/thumb/55/3e/553eb4f6f225953ed2dfb2c7e337152057dd385f_180.jpg)
- Encrypt files testout lab simulator pdf#
- Encrypt files testout lab simulator software#
- Encrypt files testout lab simulator Pc#
Configure the IP address, subnet mask, and default gateway settings on PC-B.Ī. Configure the IP address, subnet mask, and default gateway settings on PC-A.ī.
Encrypt files testout lab simulator Pc#
Part 2: Configure Devices and Verify Connectivity Step 1: Configure the PC interfaces.Ī. Step 2: Initialize and reload the router and switch. Power on all the devices in the topology. Attach the devices as shown in the topology diagram, and cable as necessary.ī. Instructions Part 1: Set Up the Topology and Initialize Devices Step 1: Cable the network as shown in the topology.Ī. If using another model Cisco router, it may be necessary to use an Ethernet crossover cable. Note: The Gigabit Ethernet interfaces on Cisco 4221 routers are autosensing and an Ethernet straightthrough cable may be used between the router and PC-B. Ethernet cables as shown in the topology.Console cables to configure the Cisco IOS devices via the console ports.2 PCs (Windows with a terminal emulation program, such as Tera Term).1 Switch (Cisco 2960 with Cisco IOS Release 15.2(2) lanbasek9 image or comparable).1 Router (Cisco 4221 with Cisco IOS XE Release 16.9.4 universal image or comparable).Consult with your instructor for the procedure to initialize and reload a router and switch. Note: Make sure that the router and switch have been erased and have no startup configurations. Refer to the Router Interface Summary Table at the end of the lab for the correct interface identifiers. Depending on the model and Cisco IOS version, the commands available and the output produced might vary from what is shown in the labs. Other routers, switches, and Cisco IOS versions can be used. The switches used in the labs are Cisco Catalyst 2960s with Cisco IOS Release 15.2(2) (lanbasek9 image). Note: The routers used with CCNA hands-on labs are Cisco 4221 with Cisco IOS XE Release 16.9.4 (universalk9 image). In Part 3, you will use SSH to connect to the router remotely and utilize the IOS commands to retrieve information from the device to answer questions about the router.įor review purposes, this lab provides the commands necessary for specific router configurations. In Parts 1 and 2, you will cable the equipment and complete basic configurations and interface settings on the router. This is a comprehensive lab to review previously covered IOS router commands. Interpret the output from the routing table.Interpret the output from the startup configuration.
Encrypt files testout lab simulator software#
Retrieve hardware and software information from the router.Assign static IPv4 and IPv6 information to the PC interfaces.Part 2: Configure Devices and Verify Connectivity Initialize and restart the router and switch.
![encrypt files testout lab simulator encrypt files testout lab simulator](https://2.bp.blogspot.com/-eL7yF-Rk6q0/WouSJhiN5TI/AAAAAAAAHjo/3yUIEfxtodYgCTYdlfGbOD_73y90mLsOQCLcBGAs/w1200-h630-p-k-no-nu/wlc-0.jpg)
Encrypt files testout lab simulator pdf#
Download PDF & PKT file Completed 100% Score:.Step 5: Display a summary list of the interfaces on the router.Step 4: Display the routing table on the router.Step 3: Display the startup configuration.Step 2: Retrieve important hardware and software information.Step 1: Establish an SSH session to R1.Step 2: Initialize and reload the router and switch.
![encrypt files testout lab simulator encrypt files testout lab simulator](https://i.stack.imgur.com/AaqKJ.jpg)